Dr.Vakuum
Alle Anwendungen

Steel and foundry degassing (VD, VOD) and vacuum metallurgy

7 Min. Lesezeit

Thailand's steel industry is built on electric arc furnaces melting scrap into rebar and sections, and a growing part of it makes special and stainless steels for the automotive and appliance supply chain — steels that must be degassed. Hydrogen in steel causes flakes and delayed cracking; nitrogen causes brittleness and strain ageing; carbon must be brought below 0.03 % for stainless without burning off the chromium. All three are done in a vacuum degasser: a ladle of liquid steel in a tank (VD, vacuum degassing) or with an oxygen lance (VOD, vacuum oxygen decarburisation), stirred with argon, at 0.5–2 mbar. It is the largest vacuum load in heavy industry, and the way it is pumped has changed in the last twenty years.

1. What the vacuum does to steel

At 1,600 °C the gases dissolved in steel are in equilibrium with the partial pressure of those gases above the melt, by Sievert's law — solubility proportional to the square root of the partial pressure. Lowering the pressure from 1 bar to 1 mbar cuts the equilibrium hydrogen solubility by a factor of 30. Argon bubbled through the ladle stirs the steel and carries the hydrogen and nitrogen to the surface, where the vacuum removes them. A 50-tonne heat loses hydrogen from 6 ppm to under 1.5 ppm in 15–20 minutes at 1 mbar.

VOD adds an oxygen lance: carbon in the steel reacts with oxygen to CO, and under vacuum the CO's partial pressure is so low that the reaction proceeds at a carbon level where, at atmospheric pressure, chromium would oxidise first. That is how stainless steel is decarburised without losing its chromium — and it produces a very large volume of CO gas, which is the vacuum system's design load.

Why is the gas load at its worst exactly when the pressure is lowest?

Because the volume of a kilogram of gas is inversely proportional to the pressure. During the VOD oxygen blow the CO generation is at its peak — several hundred Nm³/h from a 50-tonne heat — and the pressure must be brought down through 100, 50, 10 mbar toward 1 mbar as the carbon falls. At 1,013 mbar, 300 Nm³/h of CO is 300 m³/h; at 10 mbar it is 30,000 m³/h; at 1 mbar it is 300,000 m³/h. The vacuum system has to move hundreds of thousands of cubic metres per hour of hot, dusty, toxic gas at the end of the blow, and tens of thousands during the degassing hold. No single machine does that: the system is staged, each stage compressing the gas to a pressure where the next, smaller stage can handle its volume.

2. Steam ejectors versus mechanical sets

For sixty years the degasser's vacuum came from multi-stage steam-jet ejectors: four or five ejector stages with inter-condensers, the first stage a booster ejector of a metre or more in diameter, consuming 10–20 tonnes per hour of 10-bar steam during a heat. Ejectors have no moving parts, tolerate the dust and the heat, and are made at the steelworks' own scale. They are also the single largest steam consumer in a meltshop that often has no other use for a boiler.

Mechanical vacuum systems — banks of Roots boosters in two or three stages, backed by dry screw pumps — replaced ejectors on new degassers and in retrofits once dry screw pumps became robust enough to run on dusty gas. A mechanical set for a 50-tonne VD/VOD:

Stage Machines Inlet pressure Function
1 6–12 large boosters (10,000–30,000 m³/h each) 0.5–10 mbar Volume stage — moves the CO and argon at low pressure
2 3–6 medium boosters (3,000–6,000 m³/h) 5–50 mbar Intermediate compression
3 4–8 dry screw pumps (300–1,200 m³/h) 30–100 mbar → atmosphere Backing — compresses to atmosphere and exhausts to the CO flare or stack

Electrical consumption during a heat: 1–3 MW, for 30–40 minutes. Against 15 t/h of steam at roughly 700 kWh/t of fuel equivalent, the mechanical set uses a quarter to a third of the energy, needs no cooling water for inter-condensers, produces no contaminated condensate, and reaches 0.5 mbar more reliably because it does not depend on cooling water temperature — which, in a Thai meltshop, is 35 °C in April. Capital is higher; payback on a busy degasser is 2–4 years.

The Dr.Vakuum MB Series boosters up to the MB4200 serve the second and third booster stages and the complete sets of smaller degassers (5–20 tonne ladles for foundries and special-steel shops); the largest first-stage boosters are engineered per project. The DSI Series dry screw pumps (DSI630, DSI1200) are the backing stage.

3. Dust, heat and carbon monoxide

The gas from a degasser carries metallurgical dust — iron and chromium oxide fume, slag particles, refractory — at tens of grams per cubic metre during the oxygen blow, at 300–600 °C. Before the first booster:

  • A water-cooled gas cooler (a duct with spray or a tube cooler) brings the gas to 80–120 °C.
  • A cyclone removes the coarse dust.
  • A bag-house or cartridge filter rated for the temperature and the pressure (filtering at 1–50 mbar is unusual; the housing is a vacuum vessel) removes the fine fume to under 10 mg/m³ so the boosters' 0.3 mm clearances survive.
  • The boosters are gas-cooled types for the high differential, with dust-tolerant seals and a nitrogen purge on the shaft seals.
  • The dry screw backing pumps have inlet strainers, nitrogen purge and a water-flushed exhaust to wash out the dust that gets through.

The exhaust is CO-rich and must go to a flare or be combusted; the whole system is gas-tight and the area around the backing pumps is monitored for CO. An ejector system had the same requirement, met by the condensers' water absorbing little and the last stage venting to a stack.

4. Vacuum induction melting and investment casting

Two smaller vacuum metallurgy duties appear at specialty foundries:

Vacuum induction melting (VIM) — melting superalloys, tool steels and special alloys in an induction furnace inside a vacuum chamber at 10⁻² to 10⁻¹ mbar, to prevent oxidation and remove dissolved gas. A 1-tonne VIM furnace in a 20 m³ chamber: pump-down to 10⁻¹ mbar in 15 minutes, hold against outgassing and the metal's own vapour and the leak. A booster set — MB1200 on a DSI300, or two-stage boosters for 10⁻³ mbar — with a dust filter, as in vacuum furnaces.

Vacuum investment casting — pouring turbine blades, golf club heads, orthopaedic implants and jewellery under vacuum so the thin sections fill without air entrapment and the reactive alloys (titanium, cobalt-chrome) do not oxidise. A 1–3 m³ chamber evacuated to 10⁻¹–10⁻² mbar between pours, cycle 10–30 minutes: an MB300 on a DV175 or DSI150, with a filter for the ceramic shell dust.

Foundry vacuum moulding (V-process) — a sand mould held together by vacuum between two plastic films, −400 to −600 mbar at high flow through the sand, dusty: liquid ring (LS275-220) or Roots vacuum blowers (RBV100) with cyclones.

5. Worked plants

Plant Duty Pressure Dr.Vakuum answer
Special-steel foundry, 8 t ladle VD H and N removal, argon stir 1 mbar, 20 min 2 × MB4200 + 2 × MB1200 + 3 × DSI630, cooler, cyclone, filter
Stainless mini-mill, 50 t VOD Decarburisation + degassing 0.5–2 mbar; 300 Nm³/h CO peak First-stage boosters per project; 4 × MB4200 second stage; 6 × DSI1200 backing; flare
VIM, 1 t Melting superalloy 10⁻¹ mbar MB1200 + DSI300
Investment casting cell Titanium pour chamber 10⁻² mbar, 15 min cycle MB300 + DSI150
V-process moulding line Sand mould hold −500 mbar, 2,000 m³/h 2 × RBV125 + cyclones

Recommended Dr.Vakuum machines

Roots boosters (MB Series) — intermediate and final booster stages, complete sets for foundry degassers: MB600, MB1200, MB4200.

Dry screw (DSI Series) — backing stage, dust-tolerant with purge and flush: DSI300, DSI630, DSI1200.

Liquid ring (LT / LS Series) — alternative backing where water is plentiful and the dust is heavy (older retrofits), and V-process moulding: LT380-320, LS275-220.

Roots vacuum blowers (RBV Series) — V-process and shallow foundry duties: RBV100, RBV125.

Degasser study. Send us the ladle size, the steels and the heat schedule, and the current ejector steam consumption if there is one, and we will outline a staged mechanical set with its power and payback. Talk to an engineer.