Vacuum wood drying kilns: drying rubberwood and hardwood in days, not weeks
Thailand's furniture industry is built on rubberwood — the timber of rubber trees felled at the end of their latex life — and rubberwood has a problem: it must be dried quickly and thoroughly after sawing, or it stains blue, is attacked by borers and fungus, and warps. The conventional answer is a steam-heated kiln at 60–80 °C for three to five weeks for 50 mm stock, after a preservative dip. Vacuum kilns do the same job in four to six days, at lower temperature, with less checking and collapse, and they are spreading through the Thai industry for exactly those reasons — and for teak, which conventional kilns dry slowly and vacuum kilns dry with less colour loss.
1. Why vacuum dries wood faster
Water leaves wood in two stages: free water in the cell cavities goes first, down to the fibre saturation point (about 28–30 % moisture content), and then bound water in the cell walls, which must diffuse to the surface and is what takes the time. Drying rate is limited by how fast moisture moves through the wood, and that depends on temperature and on the difference between the vapour pressure inside the wood and outside it.
In a conventional kiln at 70 °C and atmospheric pressure, the vapour pressure of water inside the wood is 310 mbar, and the drying air around it has a partial pressure of water of perhaps 150 mbar — a driving force of 160 mbar. In a vacuum kiln at 50 °C and 100 mbar total pressure, the water inside the wood is at its boiling point (vapour pressure 123 mbar > 100 mbar total), so it boils inside the wood and the vapour is driven out by its own pressure, with an effective driving force of the entire pressure difference and a vapour that moves freely because it is not diluted by air. Diffusion is replaced by bulk flow. The wood dries two to five times faster at a lower temperature — which is why the colour, the resin and the strength survive better.
The practical envelope: 50–150 mbar absolute, 40–70 °C. Below 40 mbar the wood's surface dries too fast and checks; above 150 mbar the gain over conventional drying shrinks.
Why does a vacuum kiln need a heating method a conventional kiln does not?
Because at 100 mbar the kiln is nearly empty of air, and air was how a conventional kiln delivered heat — hot air blown over the stack by fans. At a tenth of atmospheric density, air carries a tenth of the heat, and evaporating 1 kg of water from the wood takes 2,400 kJ that must be replaced or the wood simply cools and stops drying. Vacuum kilns therefore heat the stack in one of three ways, and the choice shapes the vacuum duty:
- Hot-plate (contact): aluminium heating plates between every layer of boards, with hot water inside. Continuous vacuum; the simplest vacuum duty.
- Cyclic (discontinuous) hot-air: the kiln is vented to atmosphere and heated with hot air for 1–2 hours, then evacuated for 1–2 hours during which the heated wood boils off its water. The vacuum pump pumps the whole kiln down from atmosphere every cycle — the most demanding vacuum duty.
- Radio-frequency (RF / dielectric): electrodes in the stack heat the wood volumetrically; continuous vacuum, fastest drying, highest capital cost; used for thick hardwood and teak.
2. The vapour load and the condenser
A 20 m³ kiln holding 12 m³ of 50 mm rubberwood, dried from 60 % to 10 % moisture content: rubberwood at 600 kg/m³ dry → 7,200 kg of dry wood → 3,600 kg of water removed over a 5-day cycle, averaging 30 kg/h and peaking at 60–80 kg/h in the first day while free water leaves.
At 100 mbar and 45 °C, 70 kg/h of water vapour is roughly 70 × (8.314 × 318 / 18) / 10,000 Pa ≈ 1,000 m³/h. No kiln pump of sane size pumps that; the kiln has a condenser (a cooled coil or plate bank inside or beside the chamber, on cooling-tower water or a small chiller) that condenses the vapour at 25–30 °C — where water's vapour pressure is 32–42 mbar, so at a 100 mbar kiln pressure the condenser removes 60–70 % of the vapour; with chilled water at 10 °C (12 mbar), 85–90 %. The condensate drains through a barometric leg or a pumped receiver and is measured — the kiln operator reads the drying rate from the condensate meter.
The pump handles the remainder plus air: with a chilled condenser,
10 kg/h of residual vapour (150 m³/h at 100 mbar) plus air leakage
into a large door-sealed chamber (10–30 Nm³/h → 100–300 m³/h at 100
mbar) plus the air released from the wood. **300–450 m³/h at 100 mbar**
for a 20 m³ kiln on continuous vacuum — a LM270-155
(375 m³/h) with the condenser, or a V301
(300 m³/h) behind a well-chilled condenser.
Cyclic kilns add the pump-down: 20 m³ (minus 12 m³ of wood → ~10 m³ of free air) from atmosphere to 100 mbar in 10 minutes needs (10/0.167) × 2.3 ≈ 140 m³/h; the vapour load then rises sharply as the hot wood flashes. Cyclic kilns run 400–600 m³/h pumps for this size, and the pump-down phase is where the pump works hardest.
3. What the vapour carries
Wood vapour is not clean steam:
- Acetic and formic acid from the wood (oak, eucalyptus and many tropical hardwoods are acidic; rubberwood mildly so). Condensate pH 3–5. Cast iron pumps corrode; stainless steel liquid ring pumps are the standard kiln pump for this reason.
- Resin and terpene vapour from softwoods and teak — sticky in a pump, dissolves in oil.
- Preservative chemicals from dipped rubberwood (boron compounds, fungicides) — carried over in droplets.
- Wood dust and bark in the first evacuation.
The liquid ring pump (LM / LS Series) is the natural kiln pump: it condenses vapour in its own ring, neutralises the acid in a dosed closed-loop seal water system, passes the dust, and has a 33 mbar ultimate that leaves margin under a 60–100 mbar kiln. Its weakness in Thailand is seal water temperature — at 32 °C its capacity at 100 mbar is reduced, so a plate exchanger against the kiln's own cooling tower or a chiller keeps the ring at 20–25 °C.
The oil-sealed rotary vane pump (V Series) is used on smaller kilns and on RF kilns with efficient chilled condensers: it needs the vapour load reduced to within its water vapour capacity (the V301 handles 4.5 kg/h with ballast), gas ballast open, a cold trap or very cold condenser, and oil changes on condition, since the acid attacks the oil.
4. Kiln construction and the vacuum system
- Chamber: a horizontal steel cylinder or a rectangular box with a full-width door, stainless or coated, 6–100 m³. Leak rate is the pump's design load; a door seal that leaks 20 m³/h costs 200 m³/h of pump at 100 mbar.
- Condenser inside the chamber (hot-plate kilns) or in a separate vessel; sized for the peak vapour rate at the available cooling water temperature; condensate meter.
- Pump below the condenser outlet, with a knock-out pot for condensate and dust; stainless pipe; isolation valve.
- Pressure control: a controller holding the set pressure by throttling or by a VSD on the pump; the drying schedule is a pressure–temperature table, not a humidity one.
- Vent: filtered atmospheric air for cyclic kilns and for release.
- Exhaust: outside, through a mist separator on oil-sealed pumps; the air smells of wood acids.
5. Worked kilns
| Kiln | Volume / charge | Type | Pump duty | Dr.Vakuum answer |
|---|---|---|---|---|
| Small hardwood kiln | 6 m³ / 3 m³ teak | Hot-plate, continuous | ~100 m³/h at 80 mbar | LM200-065, stainless, chilled seal water |
| Rubberwood kiln (above) | 20 m³ / 12 m³ | Hot-plate, continuous | ~400 m³/h at 100 mbar | LM270-155 + condenser |
| Cyclic hot-air kiln | 30 m³ / 18 m³ | Cyclic | 600 m³/h, pump-down every 2 h | LS275-220 (650 m³/h) |
| RF kiln, thick teak | 15 m³ / 8 m³ | RF, continuous, 60 mbar | ~250 m³/h, chilled condenser | V301 + cold condenser, ballast, or LM230-120 |
| Multi-kiln plant, 4 × 20 m³ | 80 m³ | Hot-plate, continuous, staggered | ~1,200 m³/h at 100 mbar | 2 × LS410-320 on a header, or one per two kilns |
Recommended Dr.Vakuum machines
Liquid ring (LM / LS Series), stainless, closed-loop dosed seal water — the kiln pump: LM200-065, LM230-120, LM270-155, LS275-220, LS410-320.
Oil-sealed vane (V Series) — RF and small kilns behind a cold condenser: V140, V301.
The dried timber goes on to the presses and veneer lines covered in Plywood, veneer and laminate pressing; the physics of vapour, condensers and why pumps drown is in Gas ballast, water vapour tolerance and why pumps drown.
Kiln to pump. Tell us the chamber volume, the charge and species, the drying pressure and the cooling water you have, and we will size the condenser and the pump — and the seal water chiller if the numbers call for one. Talk to an engineer.