Printing presses and converting: feeder suction and blast air from one machine
Thailand's printing and packaging converting industry — commercial offset printers in Bangkok, folding-carton and label plants in the industrial estates, corrugated box plants everywhere — runs on air. Every sheet that enters a press is separated from the pile by blast air, lifted by suction cups, forwarded by a suction head, carried through the press on suction and air cushions and laid down in the delivery by suction. A B1 press at 15,000 sheets an hour performs that sequence four times a second, and the pump that supplies both the vacuum and the pressure is one of the hardest-working machines in the building. Most printers never think about it until the feeder starts double-sheeting.
1. What the press needs
A sheet-fed press feeder (the "stream feeder") works like this: blast air nozzles at the rear and sides of the pile loosen and float the top sheets; lifting suckers pick up the trailing edge of the top sheet; forwarding suckers take it and pass it onto the feedboard tapes; a separation air jet under the lifted sheet keeps the next one down. In the delivery, a suction roller or brake slows the sheet and lays it on the pile; suction holds sheets on transfer cylinders; air cushions keep the fresh ink from touching anything.
The quantities per press, from the press builders' utility data:
| Press format | Vacuum (free air) | Vacuum level | Blast / pressure air | Pressure |
|---|---|---|---|---|
| A3 / B3 (small format) | 15–25 m³/h | −300 to −500 mbar | 15–25 m³/h | 300–500 mbar |
| B2 (half size) | 30–50 m³/h | −400 to −600 mbar | 30–50 m³/h | 400–600 mbar |
| B1 (full size, 4–6 colour) | 60–100 m³/h | −400 to −600 mbar | 60–120 m³/h | 400–800 mbar |
| B1 with perfector / coater | 100–150 m³/h | −500 to −600 mbar | 120–200 m³/h | 600–800 mbar |
| Large format (VLF) | 150–250 m³/h | −500 to −600 mbar | 200–300 m³/h | 600–800 mbar |
The vacuum level is moderate and the flow is continuous while the press runs — the suckers are open to atmosphere between sheets, so the pump sees a steady leak rather than a cycle. The pressure side is a blower duty at a few hundred millibar.
Why one machine for both vacuum and pressure?
Because a rotary vane pump compresses air from its inlet to its outlet, and a press needs air drawn in at one and blown out at the other. A combined vacuum-pressure pump simply pipes both ports: the inlet becomes the press's vacuum supply and the outlet, instead of exhausting to atmosphere, becomes its blast air. One motor, one set of vanes, and the two flows are inherently equal — which suits a feeder, where the suckers that lift and the nozzles that blow are matched by the press designer. The pump runs at a combined differential (say −500 mbar on the inlet and +500 on the outlet, about 1 bar across the machine), which is why dry vane pumps for presses are built for a higher total pressure ratio than plain vacuum pumps. Where the press needs more pressure air than vacuum, or at different levels, a separate side channel blower supplies the blast air and the vane pump does vacuum alone.
2. Oil-free, and why that is non-negotiable
Press rooms are full of paper dust, spray powder (anti-set-off starch) and ink mist, and the sheets they handle are about to be printed, coated and folded. An oil-sealed pump in that room does two things: its exhaust puts oil mist onto the stock and into the air (the pressure port is the exhaust — oil mist would be blown directly onto the pile), and the dust it inhales makes a grinding paste with the oil. Printing has therefore been dry-running vane territory for decades: graphite vanes in a dry chamber, oil only in sealed bearings, dust tolerated by regular vane and filter changes.
The Dr.Vakuum DRK Series combined vacuum-pressure pumps are built for this duty — vacuum to −600 mbar and pressure to 600–800 mbar from one shaft, with inlet and pressure-side filters — and the DRV (vacuum) and DRD (pressure) pumps cover the single-duty positions.
3. Folders, die-cutters, stitchers and corrugated
The converting machines downstream need the same two things in different proportions:
- Buckle and knife folders: suction wheels and belts for feeding and transport, −300 to −400 mbar, 40–100 m³/h; blast air to the feeder. Combined pump or a vane pump plus a small side channel blower.
- Flat-bed die-cutters and foil stampers: suction feeder (sheet separation, as a press), suction in the delivery and stripping station; 60–150 m³/h at −500 mbar for a B1 die-cutter.
- Saddle stitchers and perfect binders: suction openers on the signature feeders, many small suckers — 30–80 m³/h at −400 mbar, per machine; a side channel blower (1SC329, 1SC429) at −200 to −300 mbar serves the shallower designs.
- Corrugated converting (flexo folder-gluers, rotary die-cutters): vacuum transfer of the board through the printing units — large flat beds with holes, holding a 1 × 2 m sheet of board at −50 to −150 mbar: a high-flow, shallow duty for side channel blowers (1SC729, 1SC929) or centrifugal blowers (CB125A), one or two per machine, with the corrugated dust filtered at the intake. The lead-edge feeder uses a blower too.
- Envelope and bag machines: many small suckers at −300 to −500 mbar, combined pumps.
4. Central systems for print halls
A plant with eight presses and a dozen converting machines has twenty or thirty pumps, each beside a noisy, dusty machine, each needing its filters changed. A central vacuum and central blast-air system — duplex or triplex dry pumps in a plant room, a vacuum ring main at −600 mbar and a pressure main at +600 mbar, with a regulator and filter at each machine — replaces them. Diversity is good (not every feeder runs at once; makeready and washup are frequent) so the central capacity is 60–70 % of the sum. Advantages beyond noise and dust: the pumps are maintained in one place, the halls are quieter, and a press is never stopped by its own pump. Against: pipework, the pressure drop over long runs (size for < 50 mbar), and a pump failure affecting several machines — hence duplex, always.
Central system pumps: DRK combined units in parallel where vacuum and pressure demands are balanced; otherwise CL claw pumps for vacuum (continuous, non-contact, −600 mbar with ease) and 2SC side channel blowers for the pressure main.
5. Dust and the filter schedule
The paper and board dust that reaches a dry vane pump abrades the vanes and packs the filters. Every press pump has an inlet filter (vacuum side) and an intake filter (pressure side), and the schedule is the maintenance:
- Check filters weekly; change at the differential indicator or when visibly grey — on a corrugated line, weekly.
- Vanes: inspect at 2,000 hours, replace at 5,000–8,000 (sooner on heavy dust); a vane set is an hour's work.
- Carbon vane dust in the pressure air: a fine filter on the pressure line to the press so graphite does not reach the sheets.
- Cooling: a dry vane pump at a 1-bar total differential runs hot; it needs 0.5 m of clear air around it and an ambient under 40 °C — a press room with the air conditioning off at night is not that.
6. Worked plants
| Machine | Vacuum | Pressure | Dr.Vakuum answer |
|---|---|---|---|
| B2 4-colour offset | 40 m³/h at −500 | 40 m³/h at +500 | DRK60 combined |
| B1 5-colour + coater | 100 m³/h at −600 | 120 m³/h at +700 | DRK140 combined, or DRV100 + DRD100 |
| B1 die-cutter | 120 m³/h at −500 | 60 m³/h at +400 | DRK140 |
| Saddle stitcher, 8 feeders | 60 m³/h at −300 | — | 1SC429 |
| Corrugated flexo folder-gluer, 2 m | 2 × 800 m³/h at −100 | lead-edge feeder 300 m³/h at +200 | 2 × 1SC929 + 1 × 1SC729 |
| Print hall, 6 presses, central | 350 m³/h at −600 (diversified) | 400 m³/h at +600 | 3 × DRK400 combined, triplex |
Recommended Dr.Vakuum machines
Combined vacuum-pressure dry vane (DRK Series) — the press pump: DRK60, DRK100, DRK140, DRK400.
Dry vane vacuum (DRV) and pressure (DRD) — where the two duties are separate: DRV100, DRD100.
Side channel blowers (1SC / 2SC Series) — stitchers, corrugated transfer, blast air: 1SC329, 1SC429, 1SC729, 1SC929, 2SC4337.
Dry claw (CL Series) — central vacuum mains: CL150, CL300.
The paper itself was made with vacuum too — see Paper machine vacuum.
Press to pump. Tell us the press model and format, or send the builder's utility sheet, and we will match a combined pump or a vacuum-plus-blower pair, and size a central system if you have more than four machines. Talk to an engineer.