Dr.Vakuum
全部应用案例

Plywood, veneer and laminate pressing: vacuum lay-up, membrane presses and veneer handling

阅读 7 分钟

Thailand is one of the world's largest exporters of rubberwood furniture and a major producer of plywood, MDF and veneered panels. Between the sawmill and the showroom, vacuum appears in three places a flat hydraulic press cannot: on membrane presses that lay a veneer or a thermoplastic foil onto a door with a profiled face, on vacuum bag presses that form curved plywood for chair shells and table edges, and on veneer handling — the suckers, tables and splicer beds that move 0.5 mm sheets of wood without tearing them. The duties are different in depth and in what they put into the pump.

1. The membrane press

A membrane (or thermofoil) press has a heated platen above and a silicone membrane below; the panels — MDF doors with routed profiles, or shaped substrates — sit on a tray under the membrane, with a sheet of PVC foil or a veneer over them. The press closes, vacuum is drawn under the membrane (and often between the membrane and the foil), air pressure or the heated platen pushes from above, and the heated foil is stretched over every contour of the door and bonded by the adhesive activated by the heat. One cycle, 60–180 seconds, wraps a tray of 6–12 doors.

Vacuum requirement:

  • Depth: −800 to −950 mbar (50–200 mbar absolute). The vacuum supplies the forming pressure where there is no platen contact — in a 10 mm deep routed groove, atmospheric pressure of 0.9 bar is what pushes the foil into the corner.
  • Speed: the tray volume (2–4 m³ of air under a 3 × 1.3 m membrane, plus the ducting) must be evacuated to working pressure in 15–30 seconds so the hot foil does not cool before it forms. For 3 m³ to 100 mbar in 20 seconds: S = (3 / 20 s) × ln(1,013/100) × 3,600 = 0.15 × 2.3 × 3,600 ≈ 1,250 m³/h — far more than the press's pump; the press therefore has a vacuum tank (1–3 m³) pumped down between cycles and dumped into the tray through a large valve, exactly as in vacuum die casting.
  • Pump: recovers the tank from ~200 to 50 mbar in the 90-second cycle: S = (2 / 90 s) × ln(200/50) × 3,600 ≈ 110 m³/h, plus the leak through the membrane seal. Press builders fit 100–300 m³/h oil-sealed rotary vane pumps — a V140 for a 3 m press, a V301 for a twin-tray press.

Why oil-sealed, when wood is where oil mist causes finish defects?

Because the membrane press needs 50–100 mbar absolute, which rules out dry vane pumps (90 mbar ultimate — no margin) and most side channel blowers, and because the press's vacuum circuit is closed: the pump draws on a tank and a tray under a membrane, the exhaust goes outside, and the doors under the foil never see the pump's air. The oil mist concern in the CNC hold-down note is about a pump that blows its exhaust into the shop where bare wood is waiting for lacquer; here the pump is in a closed loop and the product is wrapped in PVC. A dry claw pump (CL300, 50 mbar ultimate) is the oil-free option for shops that insist, with a slightly larger tank to compensate for its slower last 50 mbar.

What the pump does breathe from a membrane press: plasticiser and adhesive vapour from the hot foil and the solvent-based or PUR hot-melt adhesive, silicone volatiles from the membrane, and MDF dust from the routed doors. A knock-out pot that catches the dust and a carbon canister for the vapour, gas ballast open, and oil changes by condition — a pump on a thermofoil press runs 1,500–2,500 hours between oil changes if protected, 300 if not.

2. Vacuum bag forming of curved plywood

A curved chair shell, a bentwood table apron or a curved kitchen door front is made by laminating thin veneers or plies with glue over a one-sided mould under a vacuum bag — the plywood equivalent of composite bagging. The bag is pulled to −800 to −950 mbar and held while the glue (urea-formaldehyde, PVA or PUR) cures, 30 minutes to several hours, often with a heated mould or a radio-frequency heater.

  • Pump-down: a bag over a 1 m² mould has 50–150 L of free volume; pumped down in a minute by a 20–40 m³/h pump.
  • Hold: the leak rate of a well-sealed bag is small; the pump holds −900 mbar against bag and mould leaks and against water vapour from the glue (UF and PVA glues are water-based and give off water as they cure — at 100 mbar, water boils at 46 °C, so a heated mould above that boils the glue line unless the pressure is controlled above the water's vapour pressure). Many shops run the bag at −850 rather than −950 mbar for this reason, with a controller.
  • Several bags on one pump with a manifold and a receiver, as in the composites shop: a V63 or V140 serves six to ten moulds.
  • Formaldehyde vapour from UF glue in the pump's exhaust: duct it outside — it is an irritant and a regulated emission.

3. Veneer handling and hold-down

Sliced and peeled veneer at 0.3–0.6 mm is brittle, splits along the grain and cannot be gripped mechanically without damage. It is moved by suction: cup lifters on the dryer outfeed and clipper, suction belts on the splicer and the lay-up station, vacuum tables that hold a sheet flat for inspection and patching.

The duty is shallow and leaky: veneer is porous and often cracked, so a cup over it draws air through the wood. −100 to −300 mbar with generous flow — side channel blower territory:

  • Suction belts on a splicer: 1SC329 (144 m³/h) or 1SC429 (216 m³/h) per machine.
  • Veneer lay-up table, 1.3 × 2.6 m perforated bed: 1SC529 (312 m³/h) at −200 mbar.
  • Cup lifters on a dryer stacker, 20 cups: 1SC429.

The gas carries veneer dust and bark fibre — an inlet filter on every blower, changed weekly, and a relief valve so a blocked line cannot stall the blower.

Panel sanders and edgebanders hold panels on vacuum beds or carry them on suction tracks: −200 to −400 mbar, high flow, sawdust — side channel blowers or, where the bed must hold a small panel against a large open area, a two-stage 2SC4337 (345–410 mbar) or 2SC6375. The CNC router hold-down duty is the same physics and is covered in its own note.

4. Dust is the whole maintenance story

Every machine in this note breathes wood dust — MDF dust being the worst, fine, hygroscopic and resin-laden. The protection scheme:

Machine Dust path Protection
Membrane press pump Routed MDF dust from the tray Tank as settling chamber, knock-out pot with drain, 5 µm inlet filter
Bag press pump Glue squeeze-out, little dust Resin trap flask per bag, carbon canister
Veneer blowers Veneer dust, bark, splinters 25 µm inlet filter with differential indicator, weekly change; relief valve
Sander / edgebander blowers Fine sanding dust Cyclone + filter; blower on the clean side

Blow the filters out with compressed air daily in a plywood plant; replace at the indicator. A dry vane or claw pump on dust duty needs its vanes or clearances inspected at 2,000 hours.

5. Worked plant: a kitchen-door factory

Three membrane presses (3 × 1.3 m, single tray), one bag-forming station with 8 moulds, two veneer splicers, one lay-up table, one wide-belt sander with vacuum bed.

Machine Duty Dr.Vakuum answer
Membrane presses (3) 50–100 mbar abs, tank recovery ~110 m³/h each 3 × V140, 2 m³ tanks, knock-out pots, carbon canisters
Bag forming, 8 moulds −850 mbar, manifold V63, 200 L receiver, resin traps
Veneer splicers (2) −200 mbar, 150 m³/h each 2 × 1SC429 + filters
Lay-up table −200 mbar, 300 m³/h 1SC529 + filter
Sander bed −300 mbar, 300 m³/h, fine dust 2SC6375 + cyclone + filter

Recommended Dr.Vakuum machines

Single-stage oil-sealed vane (V Series) — membrane and bag presses: V63, V140, V301.

Dry claw (CL Series) — oil-free membrane press option: CL300.

Side channel blowers (1SC / 2SC Series) — veneer handling, lay-up tables, sander beds: 1SC329, 1SC429, 1SC529, 2SC4337, 2SC6375.

The timber these panels are made from was dried in a kiln — and increasingly a vacuum one; see Vacuum wood drying kilns.

Line to pumps. Tell us the press sizes and cycle, the number of bag moulds and the handling stations, and we will return a pump and blower schedule with the dust protection for each. Talk to an engineer.