Dr.Vakuum
All applications

Glass, brick and ceramics: vacuum holding, forming and clay de-airing

7 min read

Glass, bricks and ceramics are among Thailand's oldest manufacturing industries and among its most modern — float glass and automotive glazing lines in Rayong, sanitaryware and tile plants in Saraburi, and brick works in every province. They use vacuum in three ways that have little in common except a working pressure within a few hundred millibar of atmosphere and a gas full of hard, fine, abrasive dust — silica, alumina, clay — that destroys pumps built for cleaner work.

1. Glass: lifting, positioning and holding

Float glass is handled by vacuum lifters from the moment it leaves the tin bath: stacking, destacking, loading into cutting tables, positioning for tempering and lamination. A sheet of 6 mm glass 3.2 × 2.5 m weighs 120 kg; a 12 mm sheet 240 kg. Lifters carry eight to twenty-four cups, and because glass is non-porous and smooth, the duty is the easiest case of the pick-and-place note: deep vacuum (−600 to −800 mbar) on a sealed load, negligible leak, sized by the pump-down of the cups and manifold and by the EN 13155 requirement to hold the load for five minutes after power failure.

  • Glass lifter pumps are small dry vane or oil-sealed vane pumps (10–40 m³/h) with a reservoir and non-return valve: DRV10, DRV25 for gantry lifters; V21 where −850 mbar is specified for heavy sheets.
  • Cutting tables hold the sheet by vacuum through a porous or perforated bed — a leaky duty like a CNC router's, served by a side channel blower (1SC429, 1SC529) at 200–300 mbar.
  • Glass dust (from cutting and edge grinding) is the hazard: silica at 1–10 µm, which cuts vanes and seals. An inlet filter at 5 µm with a differential gauge on every glass-handling pump.

In the laminating line, windscreens and architectural laminates are de-aired in vacuum bags or rings before the autoclave — a duty like composite vacuum bagging: −900 mbar held for 10–20 minutes while the glass–PVB–glass sandwich is heated to 100 °C, an oil-sealed V40 or V63 per station with a manifold.

2. Ceramics: forming under vacuum

Pressure casting of sanitaryware (toilets, basins) injects slip into porous resin moulds at 10–40 bar; vacuum enters at demoulding — the mould halves are separated and the piece released by applying vacuum and air through the porous mould, a small, shallow (−300 to −500 mbar), slip-wet duty: a DRV40 per casting machine with a slip separator.

Vacuum-assisted slip casting and isostatic pressing of tableware use vacuum to de-air the slip before casting (−900 mbar, a stirred tank — V63 with a knock-out pot) and to hold the ware on vacuum chucks for glazing and finishing (shallow, leaky, dusty — a 1SC229 side channel blower per station, with a filter).

Tile presses use vacuum on the die to remove air from the powder before pressing on large formats (−500 mbar, short pulses; a DRV60 with a receiver and a cyclone on the inlet, since the gas is spray-dried body powder).

Why does de-airing the clay change the fired brick?

Because clay for extrusion is a stiff paste of mineral particles, water and air — air folded in during mixing and present in the pores of the raw clay. An extruded column with air in it has voids that weaken the green brick, laminations where the column folded over an air pocket in the die, and cracks in firing where trapped air expands. De-aired clay packs more densely, extrudes with less pressure and a smoother surface, has 10–20 % higher green strength (fewer breakages in handling and setting), and fires to a denser, stronger, less absorbent product. The de-airing chamber on an extruder is therefore the single most important quality step in a brick or roof tile plant, and the vacuum level in it is monitored like a kiln temperature.

3. Brick and tile: the de-airing extruder

The vacuum pug mill / de-airing extruder works in two stages: a mixer-pug stage shreds the clay into thin ribbons through a perforated plate into a vacuum chamber; the ribbons' large surface exposes the air; the chamber is held at −850 to −950 mbar (50–150 mbar absolute); the de-aired clay falls into the extrusion auger below, which forms the column and, being full of clay, seals the chamber at its outlet. The clay column leaving the die is itself the vacuum seal.

The pump duty:

  • Air released from the clay: 1–3 % of the clay volume at atmospheric conditions; a 30 t/h extruder (about 15 m³/h of clay) releases 0.2–0.5 Nm³/h of air. Tiny.
  • Air leakage: through the clay seal at the inlet (the shredder plate), through shaft seals on the mixer and auger, through inspection doors — 5–20 Nm³/h on a well-kept machine, more on an old one. This is the design load.
  • Water vapour: clay at 20–25 % moisture, warm from mixing, in a 100 mbar chamber: the chamber air is saturated at the clay temperature (30–40 °C: 42–74 mbar vapour pressure), so vapour is half or more of the gas by volume.
  • Clay dust and fine clay particles entrained from the shredding, and occasional clay slugs when the chamber fills.

Twenty Nm³/h of air at 100 mbar with 50 % vapour is about 400 m³/h of actual volume, and the standard machine is a liquid ring pump — LM270-155 (375 m³/h) or LS275-220 (650 m³/h) for a large extruder — because the gas is wet and dirty, the clay that gets through is washed out by the seal water, and the 33 mbar ultimate is well below the 50–100 mbar set point. Brick works have run liquid ring pumps on extruders for seventy years for exactly these reasons; the seal water tank fills with clay and is cleaned weekly, and the pump is stainless or cast iron depending on the clay's chemistry (some clays are sulphate-rich and acidic).

Dry alternatives for plants without water: an oil-sealed V301 behind a cyclone, a cartridge filter and a knock-out pot — workable on a dry-pressed body, poor on a wet extrusion clay where the vapour and dust together make a paste in the filter. A dry claw (CL300, 50 mbar) with the same protection on smaller extruders.

Installation: a knock-out pot of 200–500 L at the extruder outlet with a clay dump door at the bottom (what collects is clay — returned to the mixer), a sight glass on the chamber, a vacuum gauge visible to the operator, an inlet strainer at the pump, and the pump mounted below the chamber outlet so the line drains toward the pot, not the pump.

4. Dust protection across all three industries

Dust Size Hardness Protection
Glass / silica 1–20 µm Very hard, abrasive 5 µm pleated filter, differential gauge; dry vane preferred over oil-sealed (no grinding paste)
Spray-dried ceramic body 50–500 µm, free-flowing Hard Cyclone + cartridge; receiver as settling chamber
Clay (wet) Fine, sticky Moderate Liquid ring washes it out; knock-out pot; strainer
Glaze overspray 1–50 µm, wet Moderate Water-wash separator or liquid ring
Kiln-car and refractory dust Coarse Hard Cyclone, coarse filter; Roots blower with wide clearances for central cleaning

5. Worked plants

Plant Duty Pressure Flow Dr.Vakuum answer
Float glass stacker, 24 cups Non-porous lift, 5-min hold −700 mbar 15 m³/h + reservoir DRV25, 100 L reservoir, NRV
Glass cutting table, 3.6 × 2.6 m Leaky hold-down −250 mbar 300 m³/h 1SC529 + filter
Windscreen de-airing, 6 bag stations Bag hold, 100 °C −900 mbar 60 m³/h manifold V63 + manifold + traps
Sanitaryware pressure casting, 8 machines Demould −400 mbar 8 × 20 m³/h 8 × DRV25 with slip separators, or central CL150
Brick extruder, 30 t/h De-airing chamber 80 mbar abs ~400 m³/h wet LM270-155, 300 L knock-out pot
Roof tile extruder, 60 t/h, two chambers De-airing 60 mbar abs ~800 m³/h wet LS275-220 or 2 × LM270-155

Recommended Dr.Vakuum machines

Liquid ring (LM / LS Series) — clay de-airing, wet and dirty: LM230-120, LM270-155, LS275-220.

Side channel blowers (1SC Series) — glass tables, ceramic chucks, leaky holding: 1SC229, 1SC429, 1SC529.

Dry rotary vane (DRV Series) — glass lifters, demoulding, tile presses: DRV10, DRV25, DRV40, DRV60.

Oil-sealed vane (V Series) — lamination de-airing and slip tanks: V21, V40, V63.

Centrifugal blowers (CB Series) — very shallow, very high-flow holding of light porous ware and kiln air: CB75A, CB125A.

Plant to pump. Tell us the duty — lifter, table, press or extruder — the throughput and the dust, and we will size the machine and the protection in front of it. Talk to an engineer.