Dr.Vakuum
All applications

Hospital central medical vacuum to ISO 7396-1: sizing a duplex or triplex plant

6 min read

Medical vacuum is the only vacuum system where the design standard tells you what the pumps must do if one of them fails: the plant must still meet the full design flow with the largest pump out of service. That one sentence in ISO 7396-1 (and its UK ancestor HTM 02-01, which Thai hospital projects also reference) shapes everything about how a hospital vacuum plant is sized. This note walks through the method and the equipment choices for a new or replacement plant.

1. What the system has to deliver

A medical vacuum pipeline supplies suction to terminal units (wall outlets) in wards, theatres, ICUs and recovery, for airway suction, wound drainage and surgical suction. The pipeline design pressure is −400 mbar gauge (about 600 mbar absolute) minimum at every terminal unit, with a plant set point around −450 to −600 mbar. Each terminal unit must deliver 40 L/min of free air at that pressure when tested.

That is not a deep vacuum. It is a high-flow, moderate-vacuum duty with a contaminated inlet — exactly the regime where claw and dry vane pumps live, and nowhere near where an oil-sealed pump's 0.5 mbar ultimate is of any use.

2. Sizing from terminal units and diversity

Nobody uses every outlet at once. The standard supplies diversity factors per department; the design flow is the sum over departments of (terminal units × 40 L/min × diversity). Representative values from HTM 02-01, which ISO 7396-1 Annex follows closely:

Department Diversified flow
Operating theatre (per theatre) 40 L/min for the first, +40 L/min per additional, ×0.5 after four
ICU / HDU 40 L/min per bed for the first 4 beds, then 20 L/min per bed
General ward 40 L/min for the first terminal, then 2 L/min per terminal
Accident & emergency, recovery 40 L/min per bay for first 4, then 20 L/min
Delivery / maternity 40 L/min per room

A 300-bed provincial hospital: 8 theatres, 20 ICU beds, 10 recovery bays, 240 ward beds across 12 wards, A&E with 12 bays.

  • Theatres: 4 × 40 + 4 × 20 = 240 L/min
  • ICU: 4 × 40 + 16 × 20 = 480 L/min
  • Recovery: 4 × 40 + 6 × 20 = 280 L/min
  • Wards: 12 × (40 + 19 × 2) = 936 L/min
  • A&E: 4 × 40 + 8 × 20 = 320 L/min

Design flow ≈ 2,256 L/min ≈ 135 m³/h of free air.

Why does the plant need twice the design flow?

Because ISO 7396-1 requires the plant to meet design flow with any one pump out of service, for maintenance or failure. A duplex plant therefore has two pumps each sized for 100 % of design flow; a triplex has three pumps each sized for 50 %, which is cheaper in installed power and gives a lead-lag-standby rotation. Either way the installed capacity is at least 2 × design flow, and the control system rotates the duty pump so wear is even.

For the 135 m³/h plant above:

  • Duplex: 2 × 150 m³/h — two CL150 claw pumps (150 m³/h nominal each at 50 Hz).
  • Triplex: 3 × 75 m³/h — three CL80 (75 m³/h each). Installed power 3 × 2.2 kW versus 2 × 3.5 kW, and a pump out of service leaves two running pumps at design flow.

Pumping speed must be read at the plant set point (−500 mbar gauge, roughly 500 mbar absolute), not at the free-air figure. A claw pump holds most of its displacement to that point; a side channel blower does not reach it at all.

3. Why dry claw has become the default

For decades hospital plants used oil-sealed rotary vane pumps, and many Thai hospitals still run them. New-build specifications now mostly call for dry-running claw pumps, for reasons the maintenance department understands best:

  • No oil in the working chamber. Medical vacuum inlet air is humid, carries aerosols from suction bottles and the occasional liquid slug past a failed trap. In an oil-sealed pump that contaminates the oil; in a claw pump it passes through and is drained.
  • Oil-free exhaust. The plant exhaust is piped to a safe discharge point outside the building, and ISO 7396-1 treats it as potentially infectious. A dry pump's exhaust has no oil mist to wash out and contaminate the discharge.
  • Service interval. Claw pumps are non-contact; no vanes to wear, no oil to change. Annual inspection replaces monthly oil checks.
  • Ultimate pressure that fits. Claw pumps reach 150 mbar absolute (the CL300 reaches 50 mbar) — deep enough for a −600 mbar set point with margin, shallow enough that there is no risk of pulling fluids through the pipeline.

Dry rotary vane pumps (DRV Series, 90 mbar ultimate) are the economical alternative for small clinics and dental surgeries — see the companion note on dental and clinic suction.

4. Filtration, drainage and the receiver

The plant is more than pumps. In order from the pipeline:

  1. Bacterial filters, duplexed. Two filters in parallel, each rated for the full plant flow, 99.995 % at 0.3 µm (HEPA-grade) with isolation valves so either can be changed with the plant running. Filter elements are handled as clinical waste.
  2. Drainage traps. A transparent drain flask below each filter for condensate and any liquid that has reached the plant. Checked on the daily round.
  3. Receiver. Sized so the pumps cycle no more than 6–10 starts per hour at low demand. A rule of thumb is receiver volume (L) ≈ 10–15 × design flow (m³/h), so about 1,500–2,000 L for the plant above, often as two vessels. The receiver also damps the pressure fluctuation from theatre suction switching on and off.
  4. Non-return valves and isolation on each pump so a stopped pump is not a leak path.
  5. Exhaust piped individually from each pump to outside, terminated away from air intakes and windows, with a drain at the low point. Dry pump exhaust is hot (100–140 °C); insulate where it is touchable.

5. Control, alarms and standby

  • Lead/lag/standby rotation by run hours, with automatic changeover on pressure or fault.
  • Pressure switches at the plant: normal, "plant fault" when pressure rises above set point with all pumps running, and "emergency" at −300 mbar gauge, which under ISO 7396-1 must alarm at a continuously staffed location.
  • Plant emergency alarm on the loss of any pump, and reserve running status.
  • Power supply from the hospital's essential (generator-backed) busbar; the plant restarts automatically after a power loss.
  • Variable-speed drives are optional and useful: a triplex plant on VSDs follows the night-time load at a fraction of the power and avoids the start-stop cycling that wears contactors.

6. Commissioning and the paperwork

A medical vacuum plant is a medical device installation, and the handover documentation is as important as the pumps. Commissioning to ISO 7396-1 covers pipeline pressure tests, flow at every terminal unit, alarm function tests, filter integrity and the exhaust discharge location. Keep the pump performance curves at the set point in the O&M file; the annual verification compares against them.

Recommended Dr.Vakuum machines

Dry claw pumps (CL Series) — the medical plant default: oil-free, non-contact, 150 mbar ultimate (50 mbar on CL300), continuous duty.

Model Speed, 50 Hz Motor Plant size
CL80 75 m³/h 2.2 kW Triplex up to ~150 m³/h design flow; duplex for 100-bed hospitals
CL150 150 m³/h 3.5 kW Duplex for 250–350 beds; triplex for 500 beds
CL251 250 m³/h 5.5 kW Duplex for 500–600 beds
CL300 300 m³/h 5.5 kW Large tertiary hospitals; 50 mbar ultimate

Dry rotary vane (DRV Series) — clinics, dental and small private hospitals: DRV40, DRV60.

Plant schedule. Send us the department bed and theatre counts and we will return the diversified design flow, a duplex and a triplex option with power figures, and the receiver and filter schedule. Talk to an engineer.