Dr.Vakuum

การใช้งานจริง

การประยุกต์ใช้งาน

คู่มือการเลือกขนาดและบันทึกการประยุกต์ใช้งาน — วิศวกรโรงงานในอุตสาหกรรมบรรจุภัณฑ์ อาหารและเครื่องดื่ม ยา เซมิคอนดักเตอร์ และอุตสาหกรรมหนัก กำหนดสเปกปั๊มและโบลเวอร์ Dr.Vakuum อย่างไร พร้อมแสดงวิธีคำนวณ

Battery manufacturing: electrode drying, electrolyte filling and degassing
อ่าน 7 นาที ภาษาอังกฤษ

Battery manufacturing: electrode drying, electrolyte filling and degassing

A lithium-ion cell plant uses vacuum at four points that decide the cell's life — drying the electrode coils and the assembled cell to parts-per-million moisture, filling the electrolyte into a cell whose pores would otherwise trap air, degassing after formation, and sealing. NMP and electrolyte solvent vapour in the pump, the dry-room constraint, and why the plants being built in Thailand's EV corridor specify dry screw pumps and nothing else.

ยานยนต์อิเล็กทรอนิกส์
PVD coating and metallising: from rough vacuum to high vacuum in one cycle
อ่าน 7 นาที ภาษาอังกฤษ

PVD coating and metallising: from rough vacuum to high vacuum in one cycle

A decorative chrome-look on a tap, a titanium nitride edge on a drill, an aluminium mirror inside a headlamp and the metallised film in a snack bag are all made by evaporating or sputtering metal in a chamber at 10⁻³ to 10⁻⁵ mbar. Every cycle crosses four decades of pressure, and each decade wants a different pump. Rough, fine and high-vacuum stages, batch coaters versus roll-to-roll metallisers, water vapour as the enemy, and the Dr.Vakuum set for a 2 m³ sputter chamber.

ยานยนต์อิเล็กทรอนิกส์Packaging
Vacuum heat treatment and brazing furnaces: the pump set behind a bright finish
อ่าน 7 นาที ภาษาอังกฤษ

Vacuum heat treatment and brazing furnaces: the pump set behind a bright finish

A vacuum furnace hardens tool steel, brazes aluminium heat exchangers and sinters powder-metal parts without scale or decarburisation because there is no oxygen to react with — provided the pump set reaches 10⁻² to 10⁻⁴ mbar before heating and holds it against outgassing. Pump-down time versus hot zone volume, the booster-plus-backing set, quench gas recovery, binder and oil vapour, and sizing for a 1 m³ hot zone.

ยานยนต์โลหะและโรงหล่อ
Vacuum-assisted aluminium die casting: evacuating the die in 100 milliseconds
อ่าน 6 นาที ภาษาอังกฤษ

Vacuum-assisted aluminium die casting: evacuating the die in 100 milliseconds

A high-pressure die-casting shot fills the cavity in 20–60 ms, and the air that was in it ends up as porosity unless it was removed first. Vacuum die casting pulls the cavity and shot sleeve to 50–100 mbar in the fraction of a second between pouring and injection — through a vacuum tank, not a pump. How the tank is sized, how the pump recovers it between shots, the valves that make it work, and the Dr.Vakuum DRV and V pumps on a 1,600-tonne cell.

ยานยนต์โลหะและโรงหล่อ
Vacuum impregnation of castings, motor windings and transformers
อ่าน 8 นาที ภาษาอังกฤษ

Vacuum impregnation of castings, motor windings and transformers

Vacuum impregnation fills porosity in a die casting with sealant, saturates a motor winding with varnish, and dries and fills a transformer core with oil — by pulling the air out of the voids first so the liquid can get in. The dry-vacuum, wet-vacuum and pressure steps, why castings need 1–5 mbar and windings 50–100 mbar, resin and varnish vapour in the pump, and the Dr.Vakuum V and DV machines for an autoclave line.

ยานยนต์อิเล็กทรอนิกส์โลหะและโรงหล่อ
Vacuum bagging, RTM and composite curing: holding −950 mbar for hours
อ่าน 7 นาที ภาษาอังกฤษ

Vacuum bagging, RTM and composite curing: holding −950 mbar for hours

Composite layups cure under a vacuum bag for hours, and the pump that holds them is sized by the leak rate of the bag, not by the part. Pump-down of the bag and resin volatiles, the drop test and leak budget, vacuum infusion and light RTM resin flow, several bags on one pump, and the Dr.Vakuum V and DV pumps for the composites shop.

ยานยนต์Plastics & Composites
Leak testing and brake-booster end-of-line test in automotive plants
อ่าน 6 นาที ภาษาอังกฤษ

Leak testing and brake-booster end-of-line test in automotive plants

Automotive end-of-line test stations evacuate a part to a test pressure in seconds, hold it, and watch the gauge. Pressure-decay versus helium methods, the chamber-volume-versus-cycle arithmetic, why the pump's knee sets the takt time, brake booster and fuel tank test specifics, and the Dr.Vakuum DRV and V pumps for test benches.

ยานยนต์