Dr.Vakuum

现场应用

应用案例

选型指南与应用说明 — 包装、食品饮料、制药、半导体和重工业的工程师如何为 Dr.Vakuum 真空泵和鼓风机确定规格,并给出完整计算过程。

Steel and foundry degassing (VD, VOD) and vacuum metallurgy
阅读 7 分钟 英文

Steel and foundry degassing (VD, VOD) and vacuum metallurgy

A ladle of 50 tonnes of liquid steel under a vacuum of 0.5–1 mbar gives up its hydrogen, most of its nitrogen and — with oxygen blown through it — its carbon down to stainless-steel levels. The gas load is thousands of cubic metres per hour of CO, argon and dust at a pressure where a mechanical pump's volume is at its largest; the traditional answer was a four-stage steam ejector, and the modern one is a bank of Roots boosters on dry screw pumps. How the load is estimated, how a mechanical set is staged, dust and CO handling, and the vacuum induction and investment-casting duties on the same site.

金属与铸造
Glass, brick and ceramics: vacuum holding, forming and clay de-airing
阅读 7 分钟 英文

Glass, brick and ceramics: vacuum holding, forming and clay de-airing

Three industries, three shallow-vacuum duties with abrasive dust in common. Suction cups lifting and positioning glass sheets, vacuum-assisted forming of sanitaryware and tableware, and the de-airing chamber on a brick and tile extruder that removes air from the clay column so the fired product is dense and crack-free. Flow-not-depth sizing, protecting blowers and pumps from silica and clay dust, and the Dr.Vakuum 1SC, CB, V and liquid ring machines for each.

金属与铸造Woodworking
Vacuum heat treatment and brazing furnaces: the pump set behind a bright finish
阅读 7 分钟 英文

Vacuum heat treatment and brazing furnaces: the pump set behind a bright finish

A vacuum furnace hardens tool steel, brazes aluminium heat exchangers and sinters powder-metal parts without scale or decarburisation because there is no oxygen to react with — provided the pump set reaches 10⁻² to 10⁻⁴ mbar before heating and holds it against outgassing. Pump-down time versus hot zone volume, the booster-plus-backing set, quench gas recovery, binder and oil vapour, and sizing for a 1 m³ hot zone.

汽车金属与铸造
Vacuum-assisted aluminium die casting: evacuating the die in 100 milliseconds
阅读 6 分钟 英文

Vacuum-assisted aluminium die casting: evacuating the die in 100 milliseconds

A high-pressure die-casting shot fills the cavity in 20–60 ms, and the air that was in it ends up as porosity unless it was removed first. Vacuum die casting pulls the cavity and shot sleeve to 50–100 mbar in the fraction of a second between pouring and injection — through a vacuum tank, not a pump. How the tank is sized, how the pump recovers it between shots, the valves that make it work, and the Dr.Vakuum DRV and V pumps on a 1,600-tonne cell.

汽车金属与铸造
Vacuum impregnation of castings, motor windings and transformers
阅读 8 分钟 英文

Vacuum impregnation of castings, motor windings and transformers

Vacuum impregnation fills porosity in a die casting with sealant, saturates a motor winding with varnish, and dries and fills a transformer core with oil — by pulling the air out of the voids first so the liquid can get in. The dry-vacuum, wet-vacuum and pressure steps, why castings need 1–5 mbar and windings 50–100 mbar, resin and varnish vapour in the pump, and the Dr.Vakuum V and DV machines for an autoclave line.

汽车电子金属与铸造
When a Roots booster pays: backing-pump combinations
阅读 7 分钟 英文

When a Roots booster pays: backing-pump combinations

A Roots booster multiplies a backing pump's speed by five to ten in the 0.01–10 mbar band and does nothing useful above it. Compression ratio and the 50 mbar switch-on, the overheating limit and bypass valves, booster-plus-liquid-ring and booster-plus-vane sets, and a worked furnace example.

金属与铸造选型指南