Dr.Vakuum
All applications

Sizing Roots blowers for wastewater aeration

7 min read

Aeration is typically 45–75% of a treatment plant's total electricity demand, so blower selection and control carry more energy consequence than any other decision on the site. Most of the waste is not in the blower.

1. Discharge pressure: submergence plus everything else

Static pressure from diffuser submergence is 97.9 mbar per metre of water (0.433 psi per foot). That is 80–90% of the total discharge pressure. The remaining 10–20% is the part engineers argue about, and it is where the design margin lives:

Component Typical value
Static — submergence 98 mbar per metre
Piping, valves, fittings at full flow up to 70 mbar
Diffuser head loss (clean) 30–60 mbar
Ageing and fouling margin 35–70 mbar
Inlet filter, clean → dirty 15–35 mbar
Discharge check valve under 10 mbar
Basin control valve 20–35 mbar

Municipal aeration generally needs blowers capable of under 1,000 mbar (15 psig), with real duties commonly 520–590 mbar. Tank depth runs 3–8 m municipal, 10–20 m industrial.

2. Sizing the airflow

Air is 23.2% oxygen by weight. At 20 °C and one atmosphere that is 0.28 kg O₂ per m³ of air — but referenced to 0 °C (Nm³, the European convention) it is 0.30 kg O₂ per Nm³. Mixing the two is a 7% sizing error, so state the reference condition explicitly.

Q_air = SOTR / (SOTE × 0.28)

The field oxygen requirement is not the standard one. The correction is:

AOR = SOTR × α × F × [(β·C_sat·τ − C) / C_20] × θ^(T−20)

with published values: α = 0.3–1.0 (low end for diffused aeration), F = 0.5–1.0 (fouling), β = 0.95–0.98, θ = 1.024. The combined αF averages below 0.5 for fine-pore diffused aeration.

That last figure is the one to design on. A fine-bubble system in real wastewater with real fouling transfers less than half what its clean-water datasheet claims.

3. Fine versus coarse bubble

Standard oxygen transfer efficiency scales with submergence:

  • Fine bubble: about 2% per foot — roughly 6.5% per metre
  • Coarse bubble: under 1% per foot — under 3.3% per metre

So fine bubble is roughly 2× coarse, reaching 3× only at depth. In efficiency terms, published field ranges are 1.2–2.0 kg O₂/kWh for fine bubble and 0.6–1.2 for coarse. Mechanical surface aerators sit at 1.5–2.1 kg O₂/kWh, which is comparable to fine-bubble diffused aeration — a useful corrective to the claim that diffused aeration is categorically better. It is better per unit of oxygen mainly through control, not through a large intrinsic gap.

Note that clean-water figures of 3–5 kg O₂/kWh circulate widely. They are standard-condition numbers. Do not size on them.

4. Fouling is the dominant failure mode

Diffuser fouling raises back-pressure and lowers transfer at the same time. A 50-day controlled trial measured dynamic wet pressure rise:

Membrane 200 mg/L hardness 400 mg/L 800 mg/L
EPDM +66% +126% +209%
Silicone +28% +34% +118%
Polyurethane +194% +304% +554%

Over those same 50 days, transfer efficiency fell 13–20%. You pay more pressure to move less oxygen, and both effects compound.

Two conclusions follow. First, silicone is dramatically more fouling resistant than EPDM or polyurethane — a specification decision worth making deliberately. Second, field data shows efficiency declining fastest in the first 24 months, with cleaning inside 12 months generally economic.

This is why the ageing margin in §1 is not optional. Size the blower against the fouled condition; a machine bought against a clean-water curve walks up the pressure axis into the relief valve as the diffusers load up.

It also explains a common misdiagnosis: a blower audited as "inefficient" is very often a perfectly good blower behind fouled diffusers.

5. Why a Roots blower, and where it stops being the answer

A rotary lobe blower has no internal compression. Its theoretical power is therefore not the isentropic expression but the isochoric one:

P [kW] = V₀ [m³/min] × Δp [mbar] / 600

Using the isentropic formula understates a Roots blower's power, because it credits the machine with compression it does not perform.

The consequences of having no internal compression:

  • Flow and pressure are independent at constant speed. The blower delivers its displacement against whatever pressure the system imposes, and keeps raising pressure until something yields. A relief valve upstream of the discharge isolation valve is mandatory, not optional.
  • You cannot turn the pressure down. If discharge pressure is too high, the fault is in the diffusers, piping or valves — never in the blower. This reframes most field complaints.
  • No surge. A centrifugal machine loses flow along its curve as submergence rises — giving less air exactly when the tank got deeper — and can surge destructively. A Roots blower simply does not have this failure mode, which is why it suits variable-depth duties such as SBRs.
  • Temperature rise is about 1 °C per 100 mbar. At a typical 550 mbar duty that is roughly 58 °C above inlet, so a 40 °C summer inlet is a real design constraint. Excessive pressure ratio raises temperature until impeller growth causes rotor contact and seizure.

One genuinely counter-intuitive advantage: a lobe blower's power does not depend on air properties. At constant pressure and speed it draws the same power on a cold day as a warm one — but cold air is denser and carries more oxygen per revolution, so it needs less power per kilogram of oxygen in winter. A centrifugal machine does not behave this way.

Where Roots loses: it is the least efficient of the common technologies at 45–65%, against 70–78% for a single-stage integrally geared machine. On a large, constant-pressure duty that gap compounds every hour. Above roughly 10 m submergence, screw or high-speed centrifugal machines become the better answer.

6. Turndown, and the oversizing trap

Real diurnal demand varies about 2:1, and with automatic dissolved-oxygen control blowers spend more hours near the limits of their range than at the average. Sizing for the average is sizing for a condition the plant is rarely in.

Published turndown by technology:

Technology Turndown Efficiency
Rotary lobe (Roots) 40–60% 45–65%
Multistage centrifugal 20–40% 55–70%
High-speed turbo 35–55% 65–75%
Single-stage geared 50–60% 70–78%

A Roots blower's turndown limit is thermal, not aerodynamic. Slip — back-leakage through rotor clearances — is roughly constant in absolute terms, so as displacement falls with speed it becomes a growing fraction of throughput, raising discharge temperature and cutting efficiency.

Aim for at least 50% (2:1) turndown per machine and 75% (4:1) across the system, with individual machines overlapping by at least 5% of a machine's flow so there is no gap in the envelope. A plant with a coverage gap hunts, cycles and blows off — and none of that appears on a datasheet.

Blowing off air through a relief valve as a control strategy is paying full compression power and discarding the result. Variable speed is the accepted technique.

7. Over-aeration fails twice

Design dissolved oxygen is conventionally 0.5–2.0 mg/L, historically around 2.0. Modern ammonia-based control runs as low as 0.2 mg/L. Holding a higher setpoint is not a safety margin, it is a cost:

  • Energy. Above 2.0 mg/L each additional 0.5 mg/L adds roughly 5–10% to blower power for little effluent benefit.
  • Clarifier performance. Excess dissolved oxygen breaks up floc, producing fine pin floc that will not settle and carries over as suspended solids.

Nitrification also destroys 7.14 mg of alkalinity as CaCO₃ per mg of ammonium oxidised, so alkalinity, not air, is sometimes the real constraint.

One more control point that pays: inlet pressure losses hurt more than the same loss on the discharge side. A dirty inlet filter costing 35 mbar raises the compression ratio about 3%, with a matching energy penalty — and particles that get past a neglected filter end up restricting the fine-bubble diffusers the blower feeds.

Recommended Dr.Vakuum machines

Roots blowers (RB Series) — pressure duty to 8,000 mmAq (78.5 kPa), bores from 40 to 400 mm, covering small package plants through to large municipal basins.

Model Capacity Inlet
RB065 2.07–5.17 m³/min 65 mm
RB100 5.80–13.36 m³/min 100 mm
RB150 13.32–31.84 m³/min 150 mm
RB200 17.01–51.03 m³/min 200 mm
RB250 27.72–79.70 m³/min 250 mm
RB300 58.94–159.0 m³/min 300 mm

Every frame is published as a full pressure–flow matrix across its speed range, so the duty point can be selected by pulley ratio rather than assumed.

Sizing help. Send us basin depth, diffuser type and age, design oxygen demand, and your diurnal load profile, and our engineers will size against the fouled condition and check the turndown envelope for gaps. Talk to an engineer.

See also: the digester gas these plants produce, and the machines that move it, in Biogas and landfill gas handling; and the collection network that feeds the plant in Vacuum sewerage and lift stations.