Dr.Vakuum
All applications

Inlet filtration, condensers and knock-out pots: protecting the pump

7 min read

When a vacuum pump is returned for repair, the failure is almost never the pump's design. It is bleaching earth in the vanes, sugar syrup in the oil, a slug of water through a dry screw, flux on a claw rotor. Everything that ends a pump's life passes through a 50–100 mm inlet port, and the equipment that stops it — a filter, a separator, a condenser — costs a fraction of the pump it protects. This note sets out how to choose and size each one.

1. Know the stream first

Inlet protection is designed for a specific stream, not for "dirty gas". Write down, for the worst case:

  • Particles: size range, loading (g/m³), whether sticky, abrasive or hygroscopic.
  • Liquid: free liquid (slugs, carry-over, foam) and its nature — water, oil, product, solvent.
  • Vapour: component, mass flow (kg/h), and its dew point at the pump inlet pressure and at the condenser water temperature you actually have (32 °C in Thailand, not the 15 °C of a European datasheet).
  • Temperature at the inlet: hot gas from a retort or a dryer reaches the pump at 100 °C+ and expands in it.

The protection scheme is then assembled in this order from the process to the pump: knock-out pot → condenser → filter → non-return valve → pump. Not every stream needs every element.

2. Inlet filters for particles

An inlet filter is a housing with a replaceable element — paper or cellulose for dry dust, polyester or stainless mesh for wet or sticky duty — through which the whole gas flow passes.

Rating. 5 µm for oil-sealed vane pumps (the oil film is thin and the vanes close-fitting), 10–25 µm for claw and screw pumps, 25–100 µm for liquid ring pumps and Roots blowers (which pass what gets through). Finer than needed costs pressure drop for no benefit.

Size by face velocity. The element area should give a face velocity of 1–2 m/min for paper, 3–5 m/min for polyester or mesh, at the actual inlet volume — which at 100 mbar is ten times the free-air figure. A V140 at its 132 m³/h displacement needs about 1.1–2.2 m² of paper element; a standard housing with a 0.5 m² element is undersized by a factor of two and will need changing in weeks.

Why does a correctly sized filter still ruin the pump?

Because it is changed on a calendar instead of on differential pressure. A clogging filter does not stop protecting the pump — it stops the pump. The pressure drop across a loaded paper element reaches 100–200 mbar, which the pump sees as a permanently throttled inlet: a vane pump then runs at a low inlet pressure and high compression ratio it was not sized for, the oil overheats, and the ultimate the process needs is never reached because 150 mbar of the available vacuum is lost in the filter. Fit a differential pressure gauge or switch across every inlet filter, alarm at 50 mbar, change at 80. It is the cheapest instrument on the system.

For heavy dust (conveying receivers, clay, ceramic, powder dryers) the filter is a cyclone first — removing 90 % of mass above 10 µm with no element to change — and a bag or cartridge filter second.

3. Knock-out pots and liquid separators

A knock-out pot is a vessel in which the gas slows down enough for liquid droplets to fall out before they reach the pump. It protects every pump type: liquid slugs break vanes, hydraulic-lock screw rotors, and over-fill a liquid ring pump's separator.

Size by settling velocity. For water droplets of 100 µm and above in air near atmospheric pressure, the terminal velocity is about 0.3 m/s; the vessel cross-section must bring the gas velocity below that:

A = V_actual / (0.3 × 3,600) m²

For 300 m³/h of actual inlet volume: A = 300 / 1,080 ≈ 0.28 m², a vessel of 600 mm diameter. Make it at least 1.5 diameters tall above the inlet, with the inlet tangential or against a baffle, the outlet at the top through a demister pad for the fine droplets, and a level switch in the bottom that stops the pump — or opens a drain valve — before the liquid reaches the outlet. A sight glass so the operator can see what is collecting.

At lower pressures the gas density falls and droplets settle faster; sizing at atmospheric conditions is conservative.

For foaming processes (sugar pans, fermenters, some solvents) the pot must be larger than the settling calculation, with an anti-foam dosing point, because foam does not settle at all.

4. Condensers for vapour

A condenser removes vapour by cooling the gas below the vapour's dew point at the inlet pressure. It is the most powerful protection there is, because it reduces the volume the pump has to handle, not just the damage.

Take a tray dryer evaporating 20 kg/h of water at 50 mbar. The vapour alone is 580 m³/h at the pump inlet. A condenser with 30 °C cooling water brings the gas to about 35 °C, where water's vapour pressure is 56 mbar — above the 50 mbar operating pressure, so nothing condenses. The condenser does nothing. With 7 °C chilled water the gas reaches 12 °C (vapour pressure 14 mbar), condensing about 70 % of the water: the pump sees 175 m³/h instead of 580. With a −20 °C refrigerated coil, 95 %: 30 m³/h.

Three design rules follow:

  1. Cooling medium temperature decides whether the condenser works at all. At operating pressures below about 60 mbar, cooling tower water does nothing in a Thai climate; chilled water or refrigerant is needed.
  2. The condenser pressure drop must be small (a few mbar) or the process sees a higher pressure than the pump does.
  3. Condensate must drain against the vacuum: a barometric leg (10.3 m for water), a condensate receiver with a pump-out cycle, or a level-controlled drain valve.

Shell-and-tube with the gas in the shell for easy cleaning; plate condensers for compact solvent duty; direct-contact (spray) condensers where mixing condensate with the coolant is acceptable (sugar, some chemical). Downstream of the condenser the gas is saturated at the outlet temperature, so a demister or a small knock-out pot catches the mist it carries.

5. Which pumps need what

Pump Particles Free liquid Condensable vapour
Oil-sealed vane (V, DV) 5 µm filter, mandatory Knock-out pot, mandatory Condenser where load > ballast tolerance; gas ballast open
Dry vane (DRV) 5–10 µm filter, mandatory Knock-out pot Keep pump warm; condenser for continuous vapour
Dry claw (CL) 10–25 µm filter Knock-out pot; pump passes small amounts Tolerates; drain at exhaust
Dry screw (DSI) 25 µm filter or cyclone Knock-out pot (hydraulic lock) Tolerates; nitrogen purge; condenser for recovery
Liquid ring (LM, LT, LS) 100 µm strainer; cyclone for heavy dust Tolerates slugs; separator sizing Condenses internally; pre-condenser shrinks the pump
Side channel (1SC, 2SC) 10–25 µm filter, mandatory Must not see liquid Not applicable
Roots (RBV, MB) Cyclone + 25–100 µm filter Knock-out pot Booster runs hot; backing pump decides

6. The other inlet essentials

  • Non-return (anti-suckback) valve at the pump inlet. On an oil-sealed pump, a stop against a vessel under vacuum sucks oil into the process; on any pump it lets the process back-flow. Many pumps have one built in — check, and fit one if not.
  • Isolation valve so the pump can be serviced with the system under vacuum, and so a CIP cycle cannot reach the pump.
  • Flexible connection to isolate vibration — and a short one; every metre of hose is conductance lost.
  • Gauge at the pump inlet, separate from the process gauge. The difference between the two is the pressure drop of everything in this note; when it grows, something is clogging.
  • Vacuum relief valve for blowers, which overheat against a closed inlet.

Recommended Dr.Vakuum machines and accessories

The protection is sized to the pump; the pump is sized to the duty after the protection has done its work. Every series page links the matching inlet filter and separator; for the machines that most depend on it:

  • Oil-sealed V140, V301: 5 µm inlet filter, knock-out pot, gas ballast.
  • Dry screw DSI300, DSI630: cyclone and 25 µm filter, knock-out pot, condenser for solvent recovery.
  • Liquid ring LM200-065, LS410-320: strainer on gas and seal water, pre-condenser on vapour duties.
  • Side channel 1SC529, 2SC4337: inlet filter with differential indicator, relief valve.

Which technology survives which gas is the subject of Dry, oil-sealed or liquid ring; how vapour drowns a pump and how gas ballast saves it is in Gas ballast, water vapour tolerance and why pumps drown.

Protection schedule. Send us the stream description from §1 and the pump you have or want, and we will return the filter, separator and condenser sizes — and tell you if a condenser makes a smaller pump possible. Talk to an engineer.