Dr.Vakuum
All applications

Vacuum (suction) conveying of rice, sugar and plastic granules

7 min read

A rice mill fills 25 kg bags from a hopper that was loaded by suction; a sugar refinery moves refined sugar from the dryer to the silos under vacuum; every injection moulding hall in Thailand has small hopper loaders sucking pellets from gaylords. Suction conveying — vacuum pneumatic conveying — is the dominant method for short to medium distances where the material is picked up from several points, must stay clean, or must not escape. The companion note on pressure conveying in a flour mill covers the other regime; this one covers how to design the suction side.

1. Why suction, and where it stops

In a vacuum system the blower is at the end of the line, downstream of a filter receiver that separates the product from the air. The whole pipeline runs below atmospheric pressure. Consequences:

  • Leaks pull air in, not product out — so dusty, hygienic and toxic materials stay inside, and a pipe joint that weeps does not shut down the plant.
  • Multiple pick-up points are easy: a suction nozzle or a hopper with a valve at each source, one receiver, one blower.
  • The pick-up is simple. A nozzle in a bag or a bin; no rotary valve needed at the feed end.
  • The limit is the pressure difference. Atmosphere is 1,013 mbar; a vacuum system has at most that much to spend, and practically 300–500 mbar below atmosphere before the air density falls so far that the velocity needed to keep product moving becomes impractical. Pressure systems can use 1–3 bar. So suction conveying covers up to about 50–80 m and 10–15 t/h; beyond that, pressure.

2. Dilute or dense phase

Dilute (lean) phase — the normal mode for suction. Air velocity 18–30 m/s, solids loading ratio (kg of solids per kg of air) 2–15, product fully suspended. Simple, robust, and abrasive to the product and the bends: broken rice grains and sugar dust are the price.

Dense phase under vacuum is possible for materials that fluidise well (flour, fine sugar) at loading ratios of 20–40 and velocities of 5–10 m/s, but the pressure difference available limits it to short systems, and most suction installations are dilute-phase by design.

For rice (fragile, 750 kg/m³) the design velocity is kept at the low end, 18–22 m/s, to limit breakage; refined sugar (abrasive, 850 kg/m³) at 22–26 m/s with hardened bends; plastic pellets (650 kg/m³, prone to "angel hair" streamers if the velocity is too high) at 20–25 m/s.

Why does the air flow, not the vacuum, size the blower?

Because the product is carried by air velocity, and velocity is air volume divided by pipe area. The vacuum level is just the pressure drop needed to push that air volume through the pipe with the product in it — a result, not an input. Specify the solids rate, choose a loading ratio, and the air mass flow follows; choose a velocity, and the pipe diameter follows; add up the losses, and the vacuum follows. The blower is then selected to deliver that air volume at that vacuum, read off its curve at the operating point. Starting from "we need 400 mbar" produces a system that either cannot move the product or moves it at a velocity that shatters it.

3. Sizing worked through

A rice mill conveys 8 t/h of milled rice over 35 m horizontal, 8 m vertical, with 5 bends, from two pick-up hoppers to a filter receiver above the bagging bin.

  1. Loading ratio. Dilute phase, fragile product: choose μ = 8.
  2. Air mass flow. 8,000 kg/h / 8 = 1,000 kg/h of air ≈ 830 m³/h at normal conditions (density 1.2 kg/m³).
  3. Pick-up velocity. 20 m/s at the pick-up point, where the pressure is near atmospheric. Air volume there ≈ 830 m³/h = 0.23 m³/s → pipe area 0.0115 m² → 120 mm bore (use 125 mm, DN125).
  4. Velocity at the receiver. At 350 mbar vacuum the air has expanded by 1,013/663 = 1.53 → 30 m/s in the same pipe. Acceptable; a system with a larger pressure drop would step up the pipe diameter along the route to hold velocity down.
  5. Pressure drop budget (rule-of-thumb coefficients):
    • Acceleration of solids at pick-up: ~40 mbar
    • Horizontal, 35 m with solids: ~3 mbar/m → 105 mbar
    • Vertical lift, 8 m: ~8 mbar/m → 65 mbar
    • Bends, 5 at ~15 mbar: 75 mbar
    • Filter receiver, clean to dirty: 20–40 mbar
    • Pick-up nozzle and air inlet: ~20 mbar
    • Total ≈ 350 mbar below atmosphere at the blower inlet.
  6. Blower. 830 Nm³/h of air at 350 mbar vacuum. At the inlet that is 830 × 1.53 ≈ 1,270 m³/h actual, at 663 mbar absolute.

That operating point — 1,270 m³/h at −350 mbar — is beyond a single side channel blower (a 1SC929 gives 1,134 m³/h free air but only to ~300 mbar) and squarely in Roots vacuum blower territory: an RBV125 delivers up to about 1,200 m³/h at −490 mbar maximum differential, and an RBV150 (799–1,910 m³/h) has the margin for a longer route or a wetter season. A Roots blower's near-vertical curve is a virtue here: the air flow stays constant as the filter loads and the vacuum rises.

For smaller systems — the 500 kg/h hopper loader in a moulding hall, 30 m of 50 mm pipe at −250 mbar — the arithmetic lands on 100–150 m³/h at −250 mbar, and a two-stage side channel blower such as the 2SC3315 (156 m³/h, 345 mbar maximum) or 2SC4337 (222 m³/h, 345–410 mbar) is the economical machine.

4. The filter receiver and rotary valve

The receiver is a vessel where the air slows down (cross-section sized for 1–2 m/s so the bulk of the product drops) and then passes through filter bags or cartridges that catch the fines. Reverse-pulse cleaning with compressed air keeps the pressure drop at 20–40 mbar; a receiver that loads to 100 mbar has stolen a third of the system's vacuum budget. Air-to-cloth ratio 1–1.5 m/min for sugar and flour dust, 2–3 for pellets.

Under the receiver a rotary airlock valve discharges product against the vacuum into the bin. Its leakage (air pulled in through the valve's clearances, 10–30 m³/h for a 250 mm valve at −350 mbar) is added to the blower's air flow. For batch loaders a simple flap valve replaces it: the loader fills, the blower stops or is diverted, the flap drops.

For sugar and flour, the receiver and all ducting downstream of it are ATEX / dust-explosion rated: both are explosible dusts. A relief panel on the receiver, earth bonding throughout, and a blower on the clean side of the filter so it never sees an explosible concentration.

5. Protecting the blower

The blower sits downstream of the filter and should see clean air. It does not, always:

  • Secondary filter (safety filter) between receiver and blower, so a torn bag does not send sugar into a Roots blower's 0.2 mm clearances. Differential gauge across it; a rising reading is the alarm that a bag has failed.
  • Vacuum relief valve on the inlet set 50 mbar above design: a blocked line or a closed pick-up cannot stall a side channel blower into overheating or overload a Roots blower's motor.
  • Silencers inlet and outlet; a Roots blower is 85–95 dB(A) raw.
  • Non-return valve on the blower inlet so a stopped blower does not let the receiver's dust fall back into it.

6. Energy

A vacuum conveying system runs flat out whether or not product is moving, unless controlled. Three measures pay quickly:

  • Stop the blower between batches on hopper loaders (they do), and on continuous systems a VSD to hold the pick-up velocity at the design value as the receiver filter loads — the Roots blower on a VSD follows the required air flow directly.
  • Minimum velocity, not maximum. Every 1 m/s above the saltation velocity is wasted power and added product damage.
  • Shortest route, fewest bends. Each bend costs about the same as 5 m of pipe.

Recommended Dr.Vakuum machines

System Air flow at inlet Vacuum Blower
Hopper loader, pellets, 300–800 kg/h 100–200 m³/h −200 to −300 mbar 2SC3315, 2SC4337
Small-plant central loader, 1–2 t/h 250–400 m³/h −300 to −400 mbar 2SC6375, RBV050
Rice or sugar, 3–8 t/h, 30–50 m 500–1,300 m³/h −300 to −450 mbar RBV080, RBV100, RBV125
Sugar to silos, 8–15 t/h 1,300–2,500 m³/h −350 to −490 mbar RBV150, RBV200

Roots vacuum blowers (RBV Series) — constant air flow as the filter loads, −490 mbar maximum, 59 to 3,060 m³/h. Two-stage side channel (2SC Series) — compact, quiet, oil-free loaders and small central systems.

Route to blower. Send us the material, the rate, the route (lengths, lift, bends) and the number of pick-up points, and we will return pipe size, air flow, the pressure drop budget and the blower at its operating point. Talk to an engineer.