Dr.Vakuum
All applications

Sizing vacuum for solvent recovery

7 min read

The recurring mistake in solvent-recovery vacuum design is sizing the pump on the air load. The pump is a volumetric machine, the process generates solvent as a mass flow, and converting between the two shows why that mistake is not a small one.

1. Mass in, volume out

For a vapour flow ṁ of molar mass M at absolute pressure p:

V̇ = (ṁ / M) · R · T / p

Worked at 40 °C:

Vapour At 100 mbar At 10 mbar
1 kg/h ethanol (M = 46) 20,300 m³/h 203,000 m³/h
1 kg/h toluene (M = 92) 10,200 m³/h 102,000 m³/h

Two things fall out immediately. Light solvents are volumetrically brutal — halve the molar mass and you double the volume for the same mass. And volume scales as 1/p, so dropping the setpoint by a decade multiplies the duty by ten for the same production rate.

No mechanical pump moves those volumes. This is why the condenser exists: it collapses the vapour by a factor of order 10³–10⁴ before the pump ever sees it. The pump's job is to remove non-condensables — air in-leakage, dissolved gas, inert purge — plus whatever solvent slips past the condenser.

2. Where the condenser goes, and when you need one

There is a quantitative trigger rather than a rule of thumb. A gas-ballasted pump copes unaided while the vapour partial pressure stays below

p_vapour < 0.46 × p_air

and an inlet condenser becomes necessary when p_vapour > 60 + 0.46·p_air mbar. The condenser is then sized so the pump behind it receives no more vapour than its rated tolerance — the condenser is sized to the pump, not independently.

Think of the condenser as a selective pump: it removes only the condensable fraction, and in doing so it also recovers the product. Below about 6.5 mbar vapour pressure, effective condensation needs refrigerant below 0 °C.

Solvent slip is the number that catches people. Gas leaving the condenser is saturated at the condenser temperature, so the solvent fraction is

y = P_sat(T_condenser) / P_total

Ethanol at a 10 °C condenser has P_sat ≈ 31 mbar. At 100 mbar total that is 31% solvent in the off-gas; at 50 mbar total it is 63% — the condenser is barely working, and the balance goes to the pump and the vent. Either chill harder with glycol or brine, or accept the loss. As P_total approaches P_sat(T_condenser), condensation stops entirely.

3. Why solvent inside the pump is the failure mode that drives everything

The pump compresses inlet gas to slightly above atmosphere to open the discharge valve — pressure rises to as much as 1,330 mbar before it opens. If the vapour's saturation pressure at pump temperature is exceeded during that compression, it condenses in the working chamber before it can be expelled.

A large single-stage rotary vane pump runs at 60–80 °C, giving a water vapour tolerance of roughly 40–60 mbar.

In an oil-sealed pump the failure chain is specific and self-reinforcing: solvent dissolves into the sealing oil, oil viscosity collapses, the film that seals the vane tips and lubricates them fails, ultimate pressure degrades because the diluted oil now has its own vapour pressure, and wear accelerates. With chlorinated solvents you add acid formation and corrosion.

That single mechanism is why solvent duty pushes users off oil-sealed rotary vane. You either take the oil out of the equation, or you make the sealing liquid be the solvent so contamination stops mattering.

4. Choosing the technology

Liquid ring Dry screw Rotary vane
Range to ~33 mbar to ~10⁻² mbar 100–1 mbar single, 10⁻³ two-stage
Strength handles saturated vapour, tolerates particles, robust oil-free, minimal contamination, long service intervals compact, versatile, low cost
Weakness lower efficiency, needs service liquid needs precise thermal control; sensitive to condensation and polymerisation oil degradation under solvent

The liquid ring's 33 mbar floor is not arbitrary. Ultimate pressure is set by the vapour pressure of the service liquid at working temperature; below about twice that value the liquid flashes and cavitates, hammering the rotor. Water at 15 °C has P_sat = 17 mbar, so the practical floor is ~34 mbar — and at 30 °C cooling-tower temperature it rises to ~85 mbar. This is the whole explanation for "the liquid ring pump won't pull vacuum in summer."

Since bulk solvent stripping commonly runs 50–200 mbar, above that floor, liquid ring remains genuinely viable. Pushing to 1–10 mbar for heat-sensitive fine chemicals is what forces dry screw.

Solvent-sealed liquid ring turns the liability into an asset: seal with the process solvent itself in a closed loop, and contamination is meaningless while condensation inside the pump becomes recovery. The catch is that the solvent's own vapour pressure sets your ultimate — sealing with acetone gets you nowhere near water's figure unless the loop is chilled hard.

Counter-intuitively, run a dry pump hotter than instinct suggests. The jacket setpoint must be high enough that process gas does not condense inside it, and low enough to stay under the autoignition temperature and the ATEX class limit. Warm the pump up before process gas enters, and purge with nitrogen before shutdown — solvent condensing in a cooling pump dissolves residue and dries to a varnish, which is the most common cause of a pump seized on next start.

5. Explosion protection

ATEX zones are defined by hours per year of flammable atmosphere: Zone 0 above 1,000 h, Zone 1 from 10 to 1,000 h, Zone 2 below 10 h. Temperature class caps maximum surface temperature — T4 = 135 °C, T6 = 85 °C.

The class must sit below the solvent's autoignition temperature, and this catches people out. Toluene autoignites at 480 °C, so T1 (450 °C) is nominally adequate. Ethanol autoignites at 365 °C — below the T1 limit — so T1 is not acceptable for ethanol. A dry pump's hottest internal surface is therefore a safety-critical dimension, not a comfort setting.

Three strategies remove the hazard rather than contain it, and all three are better engineering than relying on equipment rating alone:

  1. Low pressure suppresses combustion. A burn cannot be sustained below roughly 60 mbar. Deep vacuum is intrinsically safer than rough vacuum — the reverse of most people's intuition.
  2. Stay outside the flammable range, with margin: at least 60% above the UEL or below 25% of the LEL. Note both toluene (flash point 4 °C) and ethanol (13 °C) have flash points below ambient, so the headspace above either is flammable by default.
  3. Limit the oxidant. Keeping oxygen below 5% with nitrogen puts the atmosphere outside the flammable range for all but a few vapours, with a design margin of 40–60% of the limiting oxygen concentration. This is more robust than chasing the LEL, because the limiting oxygen concentration is independent of fuel concentration — you cannot be caught out by an unexpected solvent level.

A design conflict worth naming: admitting air as anti-cavitation bleed on a liquid ring pump, or as gas ballast on a rotary vane, is exactly the wrong thing to do in a flammable duty. Use nitrogen for both. Note also that under vacuum the leak direction is inward — air ingress into a solvent-saturated vessel is how an explosive mixture gets built, which is the inverse of pressure-system intuition.

6. Sizing checklist

Q_total = Q_process + Q_leak + Q_desorption, then S = Q / (p_target − p_ultimate), with pump-down t = (V/S)·ln(p₀/p₁).

  • Convert the solvent mass flow to volume at the operating pressure, not at atmosphere
  • Subtract what the condenser removes; add the saturated slip from §2
  • Air in-leakage is often the dominant non-condensable term in an industrial plant, and is routinely underestimated — estimate it from vessel volume, seal count and flange count
  • Apply a 1.3–1.5× margin, enough that the pump is never forced to its ultimate pressure (critical for liquid ring, which cavitates there)
  • Keep the pump within about 3 m of the vessel to limit conductance loss

Finally, match the seal elastomer to the solvent: FKM for aromatics and chlorinated solvents but never for ketones; FFKM for acetone, MEK and THF; EPDM for alcohols and water but not for hydrocarbons.

Recommended Dr.Vakuum machines

Liquid ring pumps (LS and LM Series) — the robust choice for vapour-saturated streams at 50 mbar and above, tolerant of carryover and capable of solvent-sealed closed-loop operation.

Model Capacity
LM230-090 195 m³/h (50 Hz)
LS410-320 1,400 m³/h (50 Hz)

Dry screw pumps (DSI Series) — oil-free with 0.05 mbar ultimate, for heat-sensitive fine chemicals and wherever recovered solvent must leave the pump uncontaminated and reusable.

Model Flow (50/60 Hz)
DSI300 300 / 360 m³/h
DSI630 630 / 756 m³/h
DSI1200 1,200 / 1,440 m³/h

Sizing help. Send us the solvent, its mass evaporation rate, the target pressure, condenser coolant temperature, and the zone classification, and our engineers will work the volumetric duty, the slip fraction and the temperature-class constraint through with you. Talk to an engineer.

See also: the column and short-path duties that produce these vapour streams in Vacuum distillation, short-path evaporation and crystallisation, and the technology choice by gas composition in Dry, oil-sealed or liquid ring.